|
The ip device provides the interface to Internet Protocol stacks.
Spec is an integer starting from 0 identifying a stack. Each stack
implements IPv4 and IPv6. Each stack is independent of all others:
the only information transfer between them is via programs that
mount multiple stacks. Normally a system uses only one
stack. However multiple stacks can be used for debugging new IP
networks or implementing firewalls or proxy services.
All addresses used are 16–byte IPv6 addresses. IPv4 addresses are
a subset of the IPv6 addresses and both standard ASCII formats
are accepted. In binary representation, all v4 addresses start
with the 12 bytes, in hex:
| |
00 00 00 00 00 00 00 00 00 00 ff ff
|
Configuring interfaces
Each stack may have multiple interfaces and each interface may
have multiple addresses. The /net/ipifc directory contains a clone
file, a stats file, and numbered subdirectories for each physical
interface.
Opening the clone file reserves an interface. The file descriptor
returned from the open(2) will point to the control file, ctl,
of the newly allocated interface. Reading ctl returns a text string
representing the number of the interface. Writing ctl alters aspects
of the interface. The possible ctl messages are those
described under Protocol directories below and these:
bind ether path
| |
| |
Treat the device mounted at path as an Ethernet medium carrying
IP and ARP packets and associate it with this interface. The kernel
will dial(2) path!0x800, path!0x86DD and path!0x806 and use the
three connections for IPv4, IPv6 and ARP respectively.
|
|
bind pkt Treat this interface as a packet interface. Assume a user
program will read and write the data file to receive and transmit
IP packets to the kernel. This is used by programs such as ppp(8)
to mediate IP packet transfer between the kernel and a PPP encoded
device.
bind netdev path
| |
| |
Treat this interface as a packet interface. The kernel will open
path and read and write the resulting file descriptor to receive
and transmit IP packets.
|
|
bind loopbackTreat this interface as a local loopback. Anything
written to it will be looped back.
unbind Disassociate the physical device from an IP interface.
add local mask remote mtu proxy|trans
try local mask remote mtu proxy|trans
| |
| |
Add a local IP address to the interface. Try adds the local address
as a tentative address if it's an IPv6 address. The mask, remote,
mtu, proxy, and ®arguments are all optional. The default mask is
the class mask for the local address. The default remote address
is local ANDed with mask. The
default mtu (maximum transmission unit) is 1514 for Ethernet and
4096 for packet media. The mtu is the size in bytes of the largest
packet that this interface can send. Specifying a mtu of 0 will
use the default. Proxy, if specified, means that this machine
should answer ARP requests for the
remote address. Ppp(8) does this to make remote machines appear
to be connected to the local Ethernet. The trans argument enables
source address translation for packets routed to the interface.
Adding the special null–address 0.0.0.0 or :: in local to a interface
makes the ip stack accept all
incoming connections regardless of the destination IP address.
This is used temporarily by ipconfig(8) to accept DHCP answers
when no IP address has been assigned yet. This can also be used
to implement a NAT gateway by accepting all incoming connections
and proxying them with trampoline(8)
to a different ip stack.
|
|
del local mask Delete a local IP address from an interface.
mtu n Set the maximum transfer unit for this device to n. The mtu
is the maximum size of the packet including any medium–specific
headers.
speed n Set the maximum transmit speed in bits per second.
delay n Set the maximum burst delay in milliseconds. (Default is
40ms) When speed has been set and packets in flight exceed the
maximum burst delay then packets send on the interface are discarded
until the load drops below the maximum.
iprouting n Allow (n is missing or non–zero) or disallow (n is 0)
forwarding packets between this interface and others.
reflect n When forwarding, allow packets from this interface to
be echoed back on the same interface.
reassemble n Reassemble IP fragments before forwarding to this
interface
bridge Enable bridging (see bridge(3)).
promiscuous Set the interface into promiscuous mode, which makes
it accept all incoming packets, whether addressed to it or not.
connect type marks the Ethernet packet type as being in use, if
not already in use on this interface. A type of –1 means `all'
but appears to be a no–op.
addmulti Media–addr
| |
| |
Treat the multicast Media–addr on this interface as a local address.
|
|
delmulti Media–addr
| |
| |
Delete the multicast address Media–addr from this interface.
|
|
scanbs Make the wireless interface scan for base stations.
headersonly Set the interface to pass only packet headers, not
data too.
add6 v6addr pfx–len [onlink auto validlt preflt]
| |
| |
Add the local IPv6 address v6addr with prefix length pfx–len to
this interface. See RFC 2461 §6.2.1 for more detail. The remaining
arguments are optional:
onlinkflag: address is `on–link'
auto flag: autonomous
validltvalid life–time in seconds
prefltpreferred life–time in seconds
|
|
del6 Delete local IPv6 addresses that have expired ther valid life–time.
ra6 keyword value ...
| |
| |
Set IPv6 router advertisement (RA) parameter keyword's value.
Known keywords and the meanings of their values follow. See RFC
2461 §6.2.1 for more detail. Flags are true iff non–zero.
recvra flag: receive and process RAs.
sendra flag: generate and send RAs.
mflag flag: ``Managed address configuration'', goes into RAs.
oflag flag: ``Other stateful configuration'', goes into RAs.
maxraint ``maximum time allowed between sending unsolicited multicast''
RAs from the interface, in ms.
minraint ``minimum time allowed between sending unsolicited multicast''
RAs from the interface, in ms.
linkmtu ``value to be placed in MTU options sent by the router.''
Zero indicates none.
reachtimesets the Reachable Time field in RAs sent by the router.
``Zero means unspecified (by this router).''
rxmitra sets the Retrans Timer field in RAs sent by the router.
``Zero means unspecified (by this router).''
ttl default value of the Cur Hop Limit field in RAs sent by the
router. Should be set to the ``current diameter of the Internet.''
``Zero means unspecified (by this router).''
routerlt sets the Router Lifetime field of RAs sent from the interface,
in ms. Zero means the router is not to be used as a default router.
|
|
Reading the interface's status file returns information about
the interface. The first line is composed of white–space–separated
fields, the first two fields are: device and maxmtu. Subsequent
lines list the ip addresses assigned to that inferface. The colums
are: ip address, network mask, network address and
valid/preferred life times in milliseconds. See readipifc in ip(2).
Routing
The file iproute controls information about IP routing. When read,
it returns one line per routing entry. Each line contains eight
white–space–separated fields: target address, target mask, address
of next hop, flags, tag, interface number, source address, source
mask. The entry used for routing an IP packet is the one
with the longest destination and source mask for which destination
address ANDed with target mask equals the target and also the
source ANDed with the source mask equals the source address. The
one–character flags are:
4 IPv4 route
6 IPv6 route
i local interface
b broadcast address
u local unicast address
m multicast route
p point–to–point route
y proxy ARP for this route
t network source address translation
The tag is an arbitrary, up to 4 character, string. It is normally
used to indicate what routing protocol originated the route.
Writing to /net/iproute changes the route table. The messages
are:
flush tagRemove routes of the specified tag, or all routes if
tag is omitted.
tag stringAssociate the tag, string, with all subsequent routes
added via this file descriptor.
add target mask nexthop
add target mask nexthop interface
add target mask nexthop source smask
add target mask nexthop interface source smask
add target mask nexthop flags interface source smask
add target mask nexthop flags tag interface source smask.
| |
| |
Add the route to the table. If one already exists with the same
target and mask, replace it. The destination interface can be
specified as either the interface's /net/ipifc/n directory number,
a local IP address on the desired interface, its bound device
name or as – when unspecified, in which case the
interface will be choosen based on the source and nexthop.
|
|
del target mask
del target mask nexthop
del target mask source smask
del target mask nexthop source smask
del target mask nexthop interface source smask
del target mask nexthop flags interface source smask
del target mask nexthop flags tag interface source smask
| |
| |
Delete the matching route.
|
|
Address resolution
The file /net/arp controls information about address resolution.
The kernel automatically updates the v4 ARP and v6 Neighbour Discovery
information for Ethernet interfaces. When read, the file returns
one line per address containing the type of medium, the status
of the entry (OK, WAIT), the IP address, the
medium address and the IP address of the interface where the entry
is valid. Writing to /net/arp administers the ARP information.
The control messages are:
add type IP–addr Media–addr Interface–IP–addr
| |
| |
Add an entry or replace an existing one for the same IP address.
The optional interface IP address specifies the interface where
the ARP entry will be valid. This is needed for IPv6 link local
addresses.
|
|
del IP–addr Delete an individual entry.
flush Remove all entries.
garp IP–addrSend a gratious ARP response for the specified IP address.
ARP entries do not time out. The ARP table is a cache with an
LRU replacement policy. The IP stack listens for all ARP requests
and, if the requester is in the table, the entry is updated. Also,
whenever a new address is configured onto an Ethernet, an ARP
request is sent to help update the table on other systems.
Currently, the only medium type is ether.
Debugging and stack information
If any process is holding /net/log open, the IP stack queues debugging
information to it. This is intended primarily for debugging the
IP stack. The information provided is implementation–defined; see
the source for details. Generally, what is returned is error messages
about bad packets.
Writing to /net/log controls debugging. The control messages are:
set arglist Arglist is a space–separated list of items for which
to enable debugging. The possible items are: ppp, ip, fs, tcp,
il, icmp, udp, compress, ilmsg, gre, tcpwin, tcprxmt, udpmsg,
ipmsg, and esp.
clear arglistArglist is a space–separated list of items for which
to disable debugging.
only addr If addr is non–zero, restrict debugging to only those
packets whose source or destination is that address.
The file /net/ndb can be read or written by programs. It is normally
used by ipconfig(8) to leave configuration information for other
programs such as dns and cs (see ndb(8)). /net/ndb may contain
up to 1024 bytes.
The file /net/ipselftab is a read–only file containing all the
IP addresses considered local. Each line in the file contains
three white–space–separated fields: IP address, usage count, and
flags. The usage count is the number of interfaces to which the
address applies. The flags are the same as for routing entries.
Protocol directories
The ip device supports IP as well as several protocols that run
over it: TCP, UDP, RUDP, ICMP, IL, GRE, and ESP. TCP and UDP provide
the standard Internet protocols for reliable stream and unreliable
datagram communication. RUDP is a locally–developed reliable datagram
protocol based on UDP. ICMP is IP's catch–all
control protocol used to send low level error messages and to
implement ping(8). GRE is a general encapsulation protocol. ESP
is the encapsulation protocol for IPsec. IL provides a reliable
datagram service for communication between Plan 9 machines but
is now deprecated.
Each protocol is a subdirectory of the IP stack. The top level
directory of each protocol contains a clone file, a stats file,
and subdirectories numbered from zero to the number of connections
opened for this protocol.
Opening the clone file reserves a connection. The file descriptor
returned from the open(2) will point to the control file, ctl,
of the newly allocated connection. Reading ctl returns a text
string representing the number of the connection. Connections
may be used either to listen for incoming calls or to initiate
calls
to other machines.
A connection is controlled by writing text strings to the associated
ctl file. After a connection has been established data may be
read from and written to data. A connection can be actively established
using the connect message (see also dial(2)). A connection can
be established passively by first using an
announce message (see dial(2)) to bind to a local port and then
opening the listen file (see dial(2)) to receive incoming calls.
The following control messages are supported:
connect ip–address!port!r local
| |
| |
Establish a connection to the remote ip–address and port. If local
is specified, it is used as the local port number. If local is
not specified but !r is, the system will allocate a restricted
port number (less than 1024) for the connection to allow communication
with Unix login and exec services.
Otherwise a free port number starting at 5000 is chosen. The connect
fails if the combination of local and remote address/port pairs
are already assigned to another port.
|
|
announce [ip–address!]port
| |
| |
Set the local IP address and port number and accept calls there.
If ip–address is left out, accept calls on any address. If port
is 0, a port is automatically choosen that is not yet announced.
If the address is *, accept calls on any address. If port is *,
accept calls on any port. If port is *, and the address
is left out, accept calls on any address and port. Announce fails
if the connection is already announced.
|
|
bind [ip–address!]port
| |
| |
Set the local IP address and port number like for a server connection
similar to the announce command. If ip–address is left out, an
address is automatically selected. If port is 0, a port is automatically
choosen that is not yet announced. This command has no actual
effect, beyond remembering the
parameters and possibly selecting an unused port. The commands
announce and connect reset both the local address and the port
according to their own parameters. This command also does not
reserve the IP address and port, another connection can use them,
even while they are registered in
a connection by this command. This exists to support emulation
of BSD sockets by the APE libraries (see pcc(1)) and is not otherwise
used.
|
|
ttl n Set the time to live IP field in outgoing packets to n.
tos n Set the service type IP field in outgoing packets to n.
ignoreadvice
| |
| |
Don't break (UDP) connections because of ICMP errors.
|
|
addmulti ifc–ip [ mcast–ip ]
| |
| |
Treat ifc–ip on this multicast interface as a local address. If
mcast–ip is present, use it as the interface's multicast address.
|
|
delmulti ipDelete the address ip from this multicast interface.
Port numbers must be in the range 1 to 32767.
Several files report the status of a connection. The remote and
local files contain the IP address and port number for the remote
and local side of the connection. The status file contains protocol–dependent
information to help debug network connections. On receiving and
error or EOF reading or writing the
data file, the err file contains the reason for error.
A process may accept incoming connections by open(2)ing the listen
file. The open will block until a new connection request arrives.
Then open will return an open file descriptor which points to
the control file of the newly accepted connection. This procedure
will accept all calls for the given protocol. See
dial(2).
TCP
TCP connections are reliable point–to–point byte streams; there
are no message delimiters. A connection is determined by the address
and port numbers of the two ends. TCP ctl files support the following
additional messages:
hangup close down this TCP connection
close graceful hangup
keepalive nturn on keep alive messages. N, if given, is the milliseconds
between keepalives (default 30000).
checksum n emit TCP checksums of zero if n is zero; otherwise,
and by default, TCP checksums are computed and sent normally.
tcpporthogdefense onoff
| |
| |
of on enables the TCP port–hog defense for all TCP connections;
onoff of off disables it. The defense is a solution to hijacked
systems staking out ports as a form of denial–of–service attack.
To avoid stateless TCP conversation hogs, ip picks a TCP sequence
number at random for keepalives. If
that number gets acked by the other end, ip shuts down the connection.
Some firewalls, notably ones that perform stateful inspection,
discard such out–of–specification keepalives, so connections through
such firewalls will be killed after five minutes by the lack of
keepalives.
|
|
UDP
UDP connections carry unreliable and unordered datagrams. A read
from data will return the next datagram, discarding anything that
doesn't fit in the read buffer. A write is sent as a single datagram.
By default, a UDP connection is a point–to–point link. Either a
connect establishes a local and remote address/port pair or after
an announce, each datagram coming from a different remote address/port
pair establishes a new incoming connection. However, many–to–one
semantics is also possible.
If, after an announce, the message headers is written to ctl,
then all messages sent to the announced port are received on the
announced connection prefixed with the corresponding structure,
declared in <ip.h>:
| |
typedef struct Udphdr Udphdr;
struct Udphdr
{
| |
uchar raddr[16]; /* V6 remote address */
uchar laddr[16]; /* V6 local address */
uchar ifcaddr[16]; /* V6 interface address (receive only) */
uchar rport[2]; /* remote port */
uchar lport[2]; /* local port */
|
};
|
Before a write, a user must prefix a similar structure to each
message. The system overrides the user specified local port with
the announced one. If the user specifies an address that isn't
a unicast address in /net/ipselftab, that too is overridden. Since
the prefixed structure is the same in read and write, it is
relatively easy to write a server that responds to client requests
by just copying new data into the message body and then writing
back the same buffer that was read.
In this case (writing headers to the ctl file), no listen nor
accept is needed; otherwise, the usual sequence of announce, listen,
accept must be executed before performing I/O on the corresponding
data file.
RUDP
RUDP is a reliable datagram protocol based on UDP, currently only
for IPv4. Packets are delivered in order. RUDP does not support
listen. One must write either connect or announce followed immediately
by headers to ctl.
Unlike TCP, the reboot of one end of a connection does not force
a closing of the connection. Communications will resume when the
rebooted machine resumes talking. Any unacknowledged packets queued
before the reboot will be lost. A reboot can be detected by reading
the err file. It will contain the message
where address and port are of the far side of the connection.
Retransmitting a datagram more than 10 times is treated like a
reboot: all queued messages are dropped, an error is queued to
the err file, and the conversation resumes.
RUDP ctl files accept the following messages:
headers Corresponds to the headers format of UDP.
hangup IP port Drop the connection to address IP and port.
randdrop [ percent ]Randomly drop percent of outgoing packets.
Default is 10%.
ICMP
ICMP is a datagram protocol for IPv4 used to exchange control
requests and their responses with other machines' IP implementations.
ICMP is primarily a kernel–to–kernel protocol, but it is possible
to generate `echo request' and read `echo reply' packets from
user programs.
ICMPV6
ICMPv6 is the IPv6 equivalent of ICMP. If, after an announce,
the message headers is written to ctl, then before a write, a
user must prefix each message with a corresponding structure,
declared in <ip.h>:
| |
/*
| |
* user level icmpv6 with control message "headers"
*/
|
typedef struct Icmp6hdr Icmp6hdr;
struct Icmp6hdr {
| |
uchar unused[8];
uchar laddr[IPaddrlen]; /* local address */
uchar raddr[IPaddrlen]; /* remote address */
|
};
|
In this case (writing headers to the ctl file), no listen nor
accept is needed; otherwise, the usual sequence of announce, listen,
accept must be executed before performing I/O on the corresponding
data file.
IL
IL is a reliable point–to–point datagram protocol that runs over
IPv4. Like TCP, IL delivers datagrams reliably and in order. Also
like TCP, a connection is determined by the address and port numbers
of the two ends. Like UDP, each read and write transfers a single
datagram.
IL is efficient for LANs but doesn't have the congestion control
features needed for use through the Internet. It is no longer
necessary, except to communicate with old standalone fs(4) file
servers. Its use is now deprecated.
GRE
GRE is the encapsulation protocol used by PPTP. The kernel implements
just enough of the protocol to multiplex it. Our implementation
encapsulates in IPv4, per RFC 1702. Announce is not allowed in
GRE, only connect. Since GRE has no port numbers, the port number
in the connect is actually the 16 bit
eproto field in the GRE header.
Reads and writes transfer a GRE datagram starting at the GRE header.
On write, the kernel fills in the eproto field with the port number
specified in the connect message.
ESP
ESP is the Encapsulating Security Payload (RFC 1827, obsoleted
by RFC 4303) for IPsec (RFC 4301). We currently implement only
tunnel mode, not transport mode. It is used to set up an encrypted
tunnel between machines. Like GRE, ESP has no port numbers. Instead,
the port number in the connect message is the
SPI (Security Association Identifier (sic)). IP packets are written
to and read from data. The kernel encrypts any packets written
to data, appends a MAC, and prefixes an ESP header before sending
to the other end of the tunnel. Received packets are checked against
their MAC's, decrypted, and queued for reading
from data. In the following, secret is the hexadecimal encoding
of a key, without a leading 0x. The control messages are:
esp alg secretEncrypt with the algorithm, alg, using secret as
the key. Possible algorithms are: null, des_56_cbc, des3_cbc,
and eventually aes_128_cbc, and aes_ctr.
ah alg secret Use the hash algorithm, alg, with secret as the key
for generating the MAC. Possible algorithms are: null, hmac_sha1_96,
hmac_md5_96, and eventually aes_xcbc_mac_96.
header Turn on header mode. Every buffer read from data starts
with 4 unused bytes, and the first 4 bytes of every buffer written
to data are ignored.
noheader Turn off header mode.
IP packet filter
The directory /net/ipmux looks like another protocol directory.
It is a packet filter built on top of IP. Each numbered subdirectory
represents a different filter. The connect messages written to
the ctl file describe the filter. Packets matching the filter
can be read on the data file. Packets written to the data file
are
routed to an interface and transmitted.
A filter is a semicolon–separated list of relations. Each relation
describes a portion of a packet to match. The possible relations
are:
ver=n the IP version must be n.
proto=n the IP protocol number must be n.
data[n:m]=exprbytes n through m following the IP header must match
expr.
iph[n:m]=expr bytes n through m of the IP packet header must match
expr.
ifc=expr the packet must have been received on an interface whose
address matches expr.
src=expr The source address in the packet must match expr.
dst=expr The destination address in the packet must match expr.
Expr is of the form:
| |
value
value|value|...
value&mask
value|value&mask
|
If a mask is given, the relevant field is first ANDed with the
mask. The result is compared against the value or list of values
for a match. In the case of ifc, dst, and src the value is a dot–formatted
IP address and the mask is a dot–formatted IP mask. In the case
of data, iph and proto, both value and mask are
strings of 2 hexadecimal digits representing 8–bit values.
A packet is delivered to only one filter. The filters are merged
into a single comparison tree. If two filters match the same packet,
the following rules apply in order (here '>' means is preferred
to):
1) protocol > data > source > destination > interface
2) lower data offsets > higher data offsets
3) longer matches > shorter matches
4) older > younger
So far this has just been used to implement a version of OSPF
in Inferno and 6to4 tunnelling.
Statistics
The stats files are read only and contain statistics useful to
network monitoring.
Reading /net/ipifc/stats returns a list of 19 tagged and newline–separated
fields representing:
| |
forwarding status (0 and 2 mean forwarding off,
default TTL
input packets
input header errors
input address errors
packets forwarded
input packets for unknown protocols
input packets discarded
input packets delivered to higher level protocols
| |
output packets
output packets discarded
output packets with no route
timed out fragments in reassembly queue
requested reassemblies
successful reassemblies
failed reassemblies
successful fragmentations
unsuccessful fragmentations
fragments created
|
|
Reading /net/icmp/stats returns a list of 26 tagged and newline–separated
fields representing:
| |
messages received
bad received messages
unreachables received
time exceededs received
input parameter problems received
source quenches received
redirects received
echo requests received
echo replies received
timestamps received
timestamp replies received
address mask requests received
address mask replies received
| |
messages sent
transmission errors
unreachables sent
time exceededs sent
input parameter problems sent
source quenches sent
redirects sent
echo requests sent
echo replies sent
timestamps sent
timestamp replies sent
address mask requests sent
address mask replies sent
|
|
Reading /net/tcp/stats returns a list of 11 tagged and newline–separated
fields representing:
| |
maximum number of connections
total outgoing calls
total incoming calls
number of established connections to be reset
number of currently established connections
segments received
| |
segments sent
segments retransmitted
retransmit timeouts
bad received segments
transmission failures
|
|
Reading /net/udp/stats returns a list of 4 tagged and newline–separated
fields representing:
| |
datagrams received
datagrams received for bad ports
| |
malformed datagrams received
datagrams sent
|
|
Reading /net/il/stats returns a list of 6 tagged and newline–separated
fields representing:
| |
checksum errors
header length errors
out of order messages
| |
retransmitted messages
duplicate messages
duplicate bytes
|
|
Reading /net/gre/stats returns a list of 1 tagged number representing:
|